Making the quiver will get you twisting, tacking, and folding. The top of the arrow is made of strings and the tip from an old can. You need to work with cotton string, wooden beads, drop cloth, and empty cans among other things. You don’t need a machine for this DIY quiver and it is customized with macramé arrows and a bow. Punch holes and secure the twine with a stapler. Attach your designs and seal the paper on a tube. Fold the paper into two and cut off the extras. It is a really slim cardboard tube, well patterned with bright colors and twines as the strap. This beautiful no-sew DIY quiver can carry just a few arrows or sticks depending on the need for your hunt. For the strap, you can crisscross some lace in and out of created holes. Attach the extras to the body before sealing it up completely. It has two patterns for the top and the body and a dangling button for the pouch. This DIY leather quiver gives you an easy project to work on. You can always use a mold to shape your design then stamp and dye. This is a scaled leather quiver with a pouch and belt that can be adjustable. Making a DIY quiver needs exceptionality to differentiate from the rest. Attach your decorative paper to the cardstock and roll then glue it and make a base. It is two way too, you can either hang it or you keep it sitting on a platform. Have you ever seen a quiver made of cardstock? This can be easily used as a centerpiece. See also 25 Homemade Bow And Arrows You Can Build For Fun Or Hunting 4. You can use copper rivets to attach the hardware to the body. Cut out the three layers for the body and pocket then sew each piece with a machine. I trust you did not expect this! But, there is a little touch of leather for the pouch and the handle. Cut the shape you desire and attach the pieces together carefully with a needle and leather glue. If you love to work around with leather then this is your sure bet? There is a combination of light brown leather for the middle and deep brown leather at the edges giving it an adorable look. First, cut the pipe to shape and sand through the edges. To make this, you will need a pipe and an end lid. There is also a special casing with a strap that this goes with so you don’t need to carry your quiver with difficulty. This is an archery quiver that is built from scratch using an HT- pipe. How To Make A Quiver Using Old Torn Pants (f) Cut off any extra tape at the narrow ends of the bow. (e) Return to the center and wrap the other half in the same manner. When you reach one end, remove the rubber band and make sure all the cardboard is covered it’s fine if you leave a little extra tape on the end. We recommend placing a rubber band around the smaller edges of the cardboard to hold them together while you tape. (d) Starting at the center, wrap the combined pieces of cardboard and ruler in the brown tape tightly minimize wrinkles, although avoiding them completely will be impossible. (c) With the ruler in the center to provide some stability, duct tape the pairs and the ruler together in the center. Take the ruler/stirring stick and insert it in the middle of the pairs, where the hand grip of the bow will be. (b) Stack the five taped pairs on top of each other. Do likewise to the others, creating five taped pairs. (a) Take two cardboard pieces, match up the wide edges, and duct tape them together. (i) Glue the other strip along the top of the quiver, again lining up the point where the two edges meet with the folded edge of vinyl, and you’re done with the quiver! This should hide the glued up edges of the scrap vinyl on the bottom of your quiver, as well as the end of your strap. (h) Glue one belt strip along the bottom of the quiver, lining up the point where the two edges meet with the folded edge of vinyl. (g) Using that measurement, cut two lengths from the belt, each just long enough to wrap entirely around the circumference of the quiver. (f) Wrap the decorative belt around the circumference of the quiver and mark the length required to encircle it. Make sure the strap is not twisted around before gluing! For extra security, you can also place duct tape over the glued portion on the inside. (e) Glue the other end of the strap on the inside of the top opening of the quiver, just below the edge of the leather vinyl. The end of the strap should be glued pointing toward the top of the quiver so that the strap will continue down off the bottom. (d) Glue one end of the strap to the bottom of your quiver. (c) Cut off the edges of the strap belt, trimming it to the desired length and removing the buckle. (b) Decide how long you want the strap to be in order to fit comfortably over your shoulder. (a) Choose which belt will function as a strap, and which will serve as decorative lining on the quiver.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |